Serial number 68L3200. This is the serial number stamped into the underside of the forearm, near the muzzle. The forearm appears to be locally made in India and it has been serial numbered to match the rifle serial number. It did not leave the factory with a serial number there apparently. PDF list of Enfield Enforcer serial numbers With a little spare time, I collated the information on the Enforcers from the sticky above into PDF format. History of the Enfield Rifle. Colt M1917 Serial Numbers. 0 Comments M- 1.

This has me a little confused.
'#4 Mk2, UF '55' is a Fazackerly made Lee Enfield #4 Mk II rifle from 1955, I have a similar rifle from the same UF '55 lot, but with an A 189xx serial number, very close but no cigar, but not an envoy or enforcer, it is chambered in .303 British, the classic Lee-Enfield load. There were versions of the Enfield as dedicated marksmanship rifles, the L39 & L41 but I'm not familiar with the markings these would have had on them, I'm assuming it would have been marked as L39, or L42 respectively, not #4 Mk II???
However the ammunition headstamp is for a 7.62mm NATO load (the L42A1), not to be confused with the L42A1 designation of the Envoy. The crosshair (cross in a circle) denotes NATO spec ammunition BTW. There may also be a green, or black spot (filled in circle) on the box.
Could you have a #4 Mk II rebarreled to 7.62mm? This was a popular conversion 'back in the day' & was used a lot for long range (1,000 Yd) competition.
Is there a caliber marking on the barrel itself? this should clarify the chambering of your exact rifle & remove confusion. The 7.62mm barrels were a lot thicker than the original .303 barrels, but this was done to handle the higher pressure of the 7.62mm load, not for anything else.
As a hint. The Lee Enfields had wood almost all the way to the muzzle, only about the last 2' of barrel being visible, they also had a wooden covering over the top of the barrel to the same point in the length. The Envoy & Enforcer rifles had a much shorter front stock which stopped about 1/2 way along the barrel length & the top of the barrel was exposed all the way to the breech. Of course this may have been changed as part of a conversion to 7.62mm.
This is my Lee Enfield #4 Mk II.
The sight, mount & cheekpiece have been added to a stock rifle by me, but you get the idea of what a #4 Mk II looks like in .303 Brit.

Sold For: $4,014

Make: British Royal Small Arms Factory (RSAF) at Enfield Lock

Spider man into the spider verse. Model: Enforcer

Enfield

Iver Johnson Enforcer Serial Numbers Lee Enfield Serial Number List. There is no 'rhyme or reason' between the issue dates of the Enforcers and there are instances of consecutive serial numbers being several years apart in issuing dates. Example: No 554 was issued to Hong Kong Police 4th October 1978 No 555 was issued to Kuwait 5th June 1981 My. Enfield Enforcer 7.62mm Sniper Rifle. Image Gallery: Product Information Enfield Enforcer 7.62mm Police Sniper Rifle, Patent no 73. This is serial number 008 with matching bolt. Around 767 of these rifles were ever made. As many as 50% or more have now been destroyed. Police forces often preferring to do this rather than sell them off.

Serial Number: 391

Year of Manufacture: 1970-1985

Enfield enforcer serial numbers online

Caliber: 7.62 x 51mm Nato

Action Type: Bolt Action with 10 Round Removable Magazine Which Can Also Be Fed by Stripper Clips

Markings: The left side of the receiver is marked “ENFORCER 7.62M/M 391 / D73 PAT. APP.FOR”. The underside of the grip behind the trigger guard is marked “V”. The bottom of the barrel has an import mark “MT GUNS Z.C. NV”. The top of the barrel at the front sight is marked “PAT. APPLN No 15572/73”. The front part of the bolt is marked with a crossed swords over “19T” proof. The right side of the cocking piece on the bolt is marked “F56”. The right side of the stock collar is marked with an arrow. The tang in front of the magazine is marked “B”.

Barrel Length: The heavy barrel is about 27” in length and 0.777” in diameter just behind the rear sight.

Sights / Optics: There is a barrel band fixed to the front of the barrel with a male dovetail running fore and aft. The front sight is a large globe mounted onto the dovetail. The globe has replaceable sight inserts and has a “donut” insert installed. The rear sight is a target type aperture sight mounted to the left side of the receiver and adjustable for windage and elevation. The base of the sight is marked “921” and the sight is marked “ Alf. J. Parker / Birmingham” and “Model T.Z. 4/47”. The top of the chamber ring is drilled and tapped for a scope mount.

Stock Configuration & Condition: The stocks are three piece walnut with a light reddish brown satin finish consisting of a buttstock, forend and handguard. The top of the handguard is flat to allow clearance for the objective lens on a scope. The buttstock has a pistol grip, Monte Carlo comb, cheekpiece and a brown recoil pad with a Parker Hale logo. The recoil pad has a black and white spacer and the grip has a black plastic checkered grip cap with white spacer. There are sling swivels mounted at the front of the magazine and on a forend/handguard band. The stock shows light handling marks with compression marks along the belly, a mark on the front edge of the grip cap and a chip at the top left corner of the stock at the receiver. There also compression marks on the bottom of the forend and on the flat of the handguard. The stocks have been re-finished, and there are light oil stains under the finish around the metal parts and what appear to be thinned areas on the edge of the cheekpiece and on the front of the grip. The LOP measures 14 ¼” from the front of the trigger to the back of the recoil pad, which is hard and slightly proud of the wood at the toe. The recoil pad is in about Good condition and the stocks rate in about Very Good overall condition.

Type of Finish: The finish is a dark black paint.

Enfield enforcer serial numbers doreen

Finish Originality: The finish is not original.

Bore Condition: The bore is bright. The rifling appears rounded on the edges, as though from wear, but we are thinking it was made this way. There is no erosion. Our bore gauge measures a ME of -0.5, which is tight for even a new barrel.

Overall Condition: This rifle retains about 90% of its current metal finish. The barrel shows handling marks through its finish along its length, and the front sight globe shows handling marks through its finish and a spot of pinprick surface erosion. The front top of the chamber ring has a thick coating of bright black paint several cavities cause by air bubbles. The sides of the receiver show small marks under the finish. The stripper clip ears show pitting and handling marks under the finish and wear through the finish on the edges. The bolt knob shows thinning. The collar shows marks under the finish, a few marks through the finish and a thick dob of black paint on the right side. The trigger guard shows marks through the finish and compression marks under the finish. The screw heads are sharp but with marks of a screwdriver. The markings are clear. Overall, this rifle rates in about Very Good condition.

Mechanics: The action functions correctly. We have not fired this rifle.

Lee Enfield 303 Serial Numbers

Box, Paperwork & Accessories: This rifle comes with the attached target sights and a 10 round magazine. The magazine has been refinished with black paint. The follower is marked “CR1256 1965” and with a “D”. The side of the magazine is marked “CR 141A 65 D”. The bottom of the magazine is marked “392.”. The magazine shows wear through the finish on the sides, with handling marks under and through the finish. It is in about Very Good condition. This rifle also comes with a blued 4X10 variable power scope. It is marked “Germany / Pecar / Berlin”. The objective is about 45mm and the reticle is a fine cross-hairs. The body of the scope shows thinning with spots of surface loss and pinprick surface erosion. There are scratches/compression marks on the tube from where scope rings were mounted. The power ring turns freely. Overall, this scope is in about Very Good condition.

Enfield Enforcer Serial Numbers 222

Our Assessment: From http://world.guns.ru/sniper/sniper-rifles/brit/enfield-l42a1-and-enforcer-e.html: “After the adoption of the 7.62x51mm round as the NATO standard rifle round in 1950s, British Royal Small Arms Factory (RSAF) at Enfield Lock developed a conversion for many surplus Lee-Enfield SMLE No.4 rifles which included a new heavy barrel chambered for 7.62mm NATO ammunition, and a shortened forend and handguard. This conversion was intended for competitive shooting when mounted with adjustable open sights. Later, the L42A1 military sniper rifle was created with the addition of a scope mounting bracket to the left side of the receiver. Early in 1970, RSAF developed a police version of the L42A1, called “Enforcer” with a more sporterized buttstock with semi-pistol grip and integral cheekpiece. It also used match type iron sights and commercial telescopic sights.”. This rifle is an Enforcer chambered in 7.62 Nato that has had its scope removed, leaving the match target sights. The metal and stock have been refinished, with marks through the new finish in both. The rifle is in about Very Good condition with a very tight bright bore that has unique looking rifling. This rifle should make someone a very nice target rifle. Although it is a little light by some standards for use as a target rifle, its weight would seem to be an advantage when firing offhand, and the British army and police sharpshooters obviously made it work very well for 15 years. It is not too heavy to be used for deer hunting, and can be used on everything from small antelope on up to elk with the right loads.